Cleanrooms
Cleanroom Pressure Cascades and Classification: How They Are Developed
How cleanroom classification and pressure cascades relate, when a cascade protects the product and when it protects people, and why differential pressure setpoints are developed for each project from classification, process, risk, containment, door and airlock strategy rather than copied.
- Published
- Author
- ALVEDA SOLUTIONS Engineering Team
- Reading time
- 5 min
On a cleanroom layout, the pressure cascade is often shown as a set of numbers in each room. Those numbers look simple, but they are the result of a chain of decisions about classification, process, risk and how people and materials move. When the numbers are copied from another facility without that chain, the cascade may exist on the drawing and fail in operation.
Classification comes first
Cleanroom classification describes how clean the air must be. ISO 14644-1 classifies cleanrooms by airborne particle concentration. In GMP for sterile products, EU GMP Annex 1 and PIC/S use Grades A to D, with limits defined for the at-rest and in-operation states and supported by microbial monitoring; other frameworks, such as those for compounding, use ISO classes directly. The right reference depends on the product and the regulatory basis of the project.
The grade of each room is set by what happens there: whether product or sterile components are exposed, whether the room is a background to a critical zone, or whether it is a preparation, transfer or support area. That room-by-room decision, recorded in the room data sheets, is the starting point for everything that follows.
What a pressure cascade is for
A pressure difference between two rooms sets the direction of air through the gaps around doors, pass-throughs and other openings. In a product-protection cascade, cleaner rooms are held at higher pressure so that air flows outwards towards less clean areas. In a containment cascade, a room where hazardous or potent materials are handled is held at lower pressure than its surroundings so that air flows inwards and the material stays in.
Many facilities need both at once: a sterile hazardous-drug room, for example, must keep particles out and keep the drug in. That is where airlock design becomes the deciding factor.
Airlock philosophy
Airlocks are usually described by the pressure they hold relative to the rooms either side:
- Cascade airlock: pressure sits between the two adjoining rooms, so air moves from the cleaner side through the airlock to the less clean side. It suits product protection where containment is not a concern.
- Bubble airlock: the airlock is at higher pressure than both sides, so air flows out of it into each room. It creates a clean barrier that pushes air into a contained room and out to the corridor.
- Sink airlock: the airlock is at lower pressure than both sides, so air flows into it from each room and is extracted. It traps air from either side, which suits containment.
The choice follows the risk being controlled on each side. Personnel and material airlocks may use different philosophies in the same suite, and the gowning sequence must still work inside whichever arrangement is chosen.
How setpoints are developed
Guidance documents describe expectations for pressure differences between rooms of different grades, and the applicable texts should be read in their current form. Within that framework, the project’s own setpoints are developed from:
- The classification of each room and of its neighbours.
- The process: open or closed operations, heat and particle sources, local exhaust, and equipment that moves air.
- Product risk and containment needs, including whether any room must be negative.
- Door strategy: number, size, swing direction, interlocks and how often each door opens.
- Airlock philosophy and the gowning and material transfer sequences.
- Construction tightness, because leakage through walls, ceilings and services affects how much air is needed to hold a difference.
- The regulatory basis of the markets, and the owner’s quality expectations.
- Measurement and control: sensor accuracy, stability and how alarms with suitable delays handle normal door openings.
An illustrative sequence
Consider a simplified product-protection suite: an unclassified corridor, a change room, a background room and a room with a critical zone. On a concept drawing the cascade may be marked qualitatively — corridor as reference, then +, ++ and +++ towards the critical room — before any number is chosen. This illustration is not a recommendation for any facility. The actual values come from the factors above, are checked against the airflow balance of the HVAC design, and are confirmed during commissioning and qualification.
Classification is verified, not assumed
A room does not hold a grade because a drawing says so. Classification is demonstrated by testing: particle counts at defined locations under the states the applicable framework requires, supported by tests of filter integrity, airflow, recovery and pressure differences. ISO 14644 describes the classification method and the ongoing monitoring that demonstrates continued compliance; GMP texts add their own expectations for sterile manufacture, including microbial monitoring and requalification at defined intervals.
This is why classification and the pressure cascade should be designed together with the test plan. Sample locations, access to filters for integrity testing, and the points where pressure is measured all need space in the layout and the ceiling, and the commissioning team needs to know which room states and door positions each test assumes.
Making the cascade work in operation
A cascade fails most often at doors and at transitions. Door openings collapse pressure differences briefly; interlocks, door closers and alarm delays decide whether that is a short, expected event or a hidden loss of control. Recovery tests during qualification, airflow visualization at critical openings and a monitoring system with sensors in agreed locations show whether the design holds. Changes after handover — a new opening, a new piece of equipment with its own exhaust — should go through change control, because they alter the balance the cascade depends on.
Key points
- Set room classifications from the process before choosing any pressure value.
- Decide for each boundary whether the cascade protects the product, people, or both.
- Choose airlock types from the risk on each side, then check that gowning still works.
- Treat setpoints as project-specific and verify them in commissioning and qualification.
This article is general technical information. It is not a substitute for the current text of the applicable regulations and guidance, or for a project-specific assessment.
Related services
Where this topic sits in ALVEDA SOLUTIONS’ engineering scope.
- Cleanroom Classification & Pressure CascadeRoom classifications, adjacencies and pressure relationships defined as one documented cascade.
- Cleanroom DesignClassified spaces with defined pressure cascades, airlocks and gowning sequences.
- HVAC EngineeringAir systems designed for cleanliness, pressure, temperature and humidity control.
- Facility Zoning & Flow StudiesClassification zones and personnel, material and waste routes resolved before the layout is fixed.